..!! New Release: CruiserSuite TP Full Unlocker v1.03 - full GDFS reconstruction !!..
Dear all,
we have just released a new version Cruiser Suite SE TP Full Unlocker v1.03 with full GDFS reconstruction feature.
For work you need UC-20 TestPoint cable and Cruiser Suite dongle. You can buy both from any of our official resellers.
IMPORTANT: All other TestPoint solutions force the phone address bus pins to 3.3V which is exceeding its maximal allowed voltage almost twice. Only the UC-20 TP cable was designed to prevent this and avoid likely flash chip damage.
UC-20 TestPoint box is a current limited variable voltage power supply with connection sensing feature.
CruiserSuite TP Full Unlocker v1.03 release info:
- added full GDFS reconstruction feature
- supports same file format as SE GDFS Backuper & Restorer
- minor changes to EROM repair functionality
All features of CruiserSuite TP Full Unlocker software:
- Component of Cruiser Suite (once you have Cruiser Suite dongle, you can use it).
- Simple to use & failsafe
- Supports full unlock of all DB2020 plattform based SonyEricsson phones (all current DB2020 CIDs)
- Supports full unlock of DB2012 plattform based phones, CID 50, 51, 52, 53; by one (single) TPSupports full unlock and repair of specific DB2010 K310, K510, W300, W810, Z530. Specific means DB2010 / CID 49, with DB2012 chip on the PCB - those models that were not previously supported by Cruiser+
- Recovery mode feature for all supported phone models (for failed EROM write)- by using testpoint stage 2
- This software is for all users who can disassemble the phone - also for inexperienced ones. (For disassembling phones, we recommend to read proper SonyEricsson service manuals.)
- Unlocking via TP Full Unlocker does not destroy phone calibration data (so typical for SadTool ... )
- For the phone safety, TestPointing requires UC-20 TP cable.
- Unlike other amateur solutions which use external battery connection to the TP, our software uses specially designed UC-20 cable which can handle different bus voltages and prevents any potential flash chip damage.
- TP is done in two stages. Once you complete TP stage 1 you don't need to repeat it anymore. Phone is then bootable via the 2nd testpoint anytime.
- PDF manual is available after installation as usual in Documents folder
Don't forget to tell everywhere that CruiserSuite is the First on the market who provide Full Unlock of DB2012 and DB2010 over 1 SINGLE TestPoint. Everybody else (DreamBox and SadTool) requires you to do testpointing in 2 stages.
ENJOY!
http://www.cruisersuite.com/
Welcome to visit official Cruiser Suite support section of this Forum by clicking here.
Download CruiserSuite TP Full Unlocker v1.03:
Part 1
Part 2
Part 3
Part 4
Part 5
Part 6
Part 7
Part 8
JAF Exe 198.56
- improved BB5 usb flashing (6220c and E66 supported). Thanks to "The SAINT" for beta testing.
Unpack in JAF folder. YOU MUST HAVE JAF SETUP 1.98.52
Download clik here!
Introduction
Cruiser Suite SE GDFS Backuper & Restorer is a utility for performing complete GDFS backup. It can also completely restore GDFS from a specified file, if the backup was made from the same phone. Under some circumstances, you may want to perfom the restore from a file which was made from a different phone. In that case security zone is not restored (it does not make any sense). You can use other software (Full Unlockers) to completely rebuild the security zone.
CAUTION: Restoring the GDFS in a phone from a backup file made from a phone different that the one being restored overwrites and destroys the unique phone specific data (e.g. calibration data, etc.). Such phone is never more guaranteed to work 100% properly (charging, radio, ...)
Cable
Supported interfaces:
- DCU-60 / DCU-65
- UC10 / UC20
Procedure
a Backup is performed in any case, except that the GDFS is damaged and unable to be read.
1. Choose the phone model
2. If you want to perform a restore, choose a GDFS backup file
3. Connect the phone:
a. via USB cable - connect the phone while holding 'C' button
b. via UC10/UC20 cable - connect the phone and double-click on the appropriate device
4. Wait until the program perfoms the desired operations
Finished
Cruiser Suite GDFS Backuper & Restorer v1.00
Diposkan oleh Cellular-tools Labs Label: Cruiser, SE Repair Solution..:: 29/07/2008 - New Release - Cruiser Suite GDFS Backuper & Restorer v1.00 ::..
Hi all GSM world,
we have just released initial version of brand new component of your Cruiser Suite - GDFS Backuper & Restorer v1.00. This tool allows you to repair all non-security zone GDFS related problems. You can do the GDFS backup and restore of any DB2012 & DB2020 phone. GDFS Backup & Restore between different phones of the same type is also possible.
The main purpose of this application is :
to create Backup of the phone state and possible Restore of the phone to this state anytime in the future.
to repair damaged GDFS by copying GDFS content from working phone to damaged phone of the same type (GDFS repair).
Cruiser Suite GDFS Backuper & Restorer v1.00:
- Initial release
- Performs GDFS backup and restore
- Supported platforms: DB2012, DB2020
Download the GDFS Backuper & Restorer from Cruiser Suite Download Section (asap) or from this Rapidshare.com link.
Full GDFS reconstruction via TP will be available very soon.
Some bb5 like 6280,6233,6234 etc shows CMT: FFFFFFFFFFFFFFFFFFFF during fbus flashing.
Many user have this problem and many question about this problem and here is 1 good solutionits normally cable problem in most of case .
Use JAF and you have to modify your cable cause most of cable available in market are not modified so u have to modified it manually .
If u cant modify then try USB flashing its simple and done by myself here are the logs as follows1st fbus 7 pin cable but not modifiy.
This sample Log error via JAF Flasher:
====================================================================
Phone Restarted...
Changing mode...
Done!Booting phone...
CMT Boot Data:
Asic ID: 000000010000022600010006010C192101003000
Asic Mode ID: 00
Asic EM ID: 00000353
Asic Public ID: 1E700117C6205A50031ED7E2E994DF7DFD4C3D75
HASH: BAF3A9C3DBFA8454937DB77F2B8852B100000000
ROM ID: 273F6D55DFAAF68F
CMT Boot File: C:\Program Files\ODEON\JAF\Flash\rap3gv3_2nd.fg
Loader version: 01.15.00 -> Revision: 0000
Patching CMT boot step1...
Patching CMT boot step2...
Patching CMT boot step3...
CMT Boot Ready
CMT Flash ID: 002F0001
CMT Flash Data: 00000000000000000000000000000000
CMT Loader: C:\Program Files\ODEON\JAF\Flash\RAP3Gv3_algo.fg
Loader version: 01.16.00 -> Revision: 0000
Patching CMT loader step1...
Patching CMT loader step3...
Getting CMT Public Keys...
CMT Loader Ready
Done!
Restarting phone...Done!
FILES SET FOR FLASHING:
MCU Flash file: NONE
PPM Flash file: NONE
CNT Flash file: NONE
APE Variant file: NONEFILES SET FOR FLASHING:
MCU Flash file: C:\Program Files\Common Files\Nokia\DataPackage\Products\RM-123\rm123_145_30005.100.mcusw
PPM Flash file: C:\Program Files\Common Files\Nokia\DataPackage\Products\RM-123\rm123_145_3005.10.ppm_cvf
CNT Flash file: C:\Program Files\Common Files\Nokia\DataPackage\Products\RM-123\rm123_145_30005.10.image_cvf
APE Variant file: NONE
Languages in ppm: English,German,French,Italian,Dutch,Spanish,Turkis h,PortugueseBacking up CRT data...
Setting FLASH MODE
Loader version: 01.15.00 -> Revision: 0000
Patching CMT boot step1...
Patching CMT boot step2...
Patching CMT boot step3...
CMT Boot ReadyLoader version: 01.16.00 -> Revision: 0000
Patching CMT loader step1...
Patching CMT loader step3...
Getting CMT Public Keys...
CMT Loader Ready
Reading CMT NPC certificate...
Reading CMT VARIANT certificate...
Reading CMT CCC certificate...
CCC not available...
Reading CMT HWC certificate...
HWC not available...
Saved to C:\Program Files\ODEON\JAF\ProgData\35454401411952_CRT_backup _1717109.rpl
Backup CRT OK!
Backing up SIMLOCK data...
Setting local mode...
Failed! Aborting!
Failed to backup LCK...
Manual mode selected, version can't be checked!
Booting phone...
CMT Boot Data:
Asic ID: 000000010000022600010006010C192101003000
Asic Mode ID: 00
Asic EM ID: 00000353
Asic Public ID: 1E700117C6205A50031ED7E2E994DF7DFD4C3D75
HASH: BAF3A9C3DBFA8454937DB77F2B8852B100000000
ROM ID: 273F6D55DFAAF68F
CMT Boot File: C:\Program Files\ODEON\JAF\Flash\rap3gv3_2nd.fg
Loader version: 01.15.00 -> Revision: 0000
Patching CMT boot step1...
Patching CMT boot step2...
Patching CMT boot step3...
CMT Boot Ready
CMT Flash ID: 002F0001
CMT Flash Data: 00000000000000000000000000000000
CMT Loader: C:\Program Files\ODEON\JAF\Flash\RAP3Gv3_algo.fg
Loader version: 01.16.00 -> Revision: 0000
Patching CMT loader step1...
Patching CMT loader step3...
Getting CMT Public Keys...
CMT Loader Ready
Operation took 0 minutes 4 seconds...
Erasing...
Operation took 1 minutes 17 seconds...
Writing...
Stage 1Sending CMT HASH for NOLO
Sending CMT HASH for KEYS
Sending CMT HASH for PRIMAPP
Sending CMT HASH for PASUBTOC
Sending CMT PUB KEYS...
Sending CMT HASH for UPDAPP
Sending CMT HASH for DSP0
Sending CMT HASH for MCUSW
Sending CMT HASH for PMM_CONF
Sending CMT HASH for SBIF_CONF
Operation took 1 minutes 59 seconds...
Reseting phone...
PPM: C:\Program Files\Common Files\Nokia\DataPackage\Products\RM-123\rm123_145_3005.10.ppm_cvfBooting phone...
CMT Boot Data:Asic ID: 000000010000022600010006010C192101003000
Asic Mode ID: 00
Asic EM ID: 00000353
Asic Public ID: 1E700117C6205A50031ED7E2E994DF7DFD4C3D75
HASH: BAF3A9C3DBFA8454937DB77F2B8852B100000000
ROM ID: 273F6D55DFAAF68FCMT
Boot File: C:\Program Files\ODEON\JAF\Flash\rap3gv3_2nd.fg
Loader version: 01.15.00 -> Revision: 0000
Patching CMT boot step1...
Patching CMT boot step2...
Patching CMT boot step3...
CMT Boot Ready
CMT Flash ID: 002F0001
CMT Flash Data: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFCMT
Loader: C:\Program Files\ODEON\JAF\Flash\RAP3Gv3_algo.fg
Loader version: 01.16.00 -> Revision: 0000
Patching CMT loader step1...
Patching CMT loader step3...
Error in cmd1 par2...
Error loading cmt loader...
============================================================================
Failed because of non modified cable.
Now if this problem occurs just simply use Dead USB flashing and urs phone will alive again here is usb flashing logs.
2nd usb logs:
==============================================================
JAF version 1.98.30
Detected PKEY: *********xx
Card life counter: 85.49%
P-key nokia module version 01.00
Detected JAF INTERFACE version: 01.AF, Driver version: 40000, Library version: 30107
JAF DCT4/BB5 LOADERS DIR: C:\Program Files\ODEON\JAF\Flash\
JAF DCT4/BB5 PRODUCT DIR: C:\Program Files\Nokia\Phoenix\Products\
JAF USB LOADERS DIR: C:\Program Files\ODEON\JAF\FlashUSB\
JAF DCT3/DCTL LOADERS DIR: C:\Program Files\ODEON\JAF\Flash3\
Changing mode...Done!
FILES SET FOR FLASHING:
MCU Flash file: NONE
PPM Flash file: NONE
CNT Flash file: NONEAPE Variant file: NONE
FILES SET FOR FLASHING:
MCU Flash file: C:\Program Files\Common Files\Nokia\DataPackage\Products\RM-123\rm123_145_30005.100.mcusw
PPM Flash file: C:\Program Files\Common Files\Nokia\DataPackage\Products\RM-123\rm123_145_3005.10.ppm_cvf
CNT Flash file: C:\Program Files\Common Files\Nokia\DataPackage\Products\RM-123\rm123_145_30005.10.image_cvf
APE Variant file: NONE
Languages in ppm: English,German,French,Italian,Dutch,Spanish,Turkis h,Portuguese
PRESS POWER ON THE PHONE NOW!!!
Searching for phone...Detected P-KEY: *********xx
P-key nokia module version 01.00
Init usb communication...Found
Starting DEAD USB phone flashing...Using 06.02.002
Elf2flash 02.31.000 RAW loader...
Patching RAW boot step1...
Patching RAW boot step3...
Sending RAW Loader......................
Loader Sent!Stage 2 starting.......................................... ................Loader Sent!
Stage 3 starting..........Phone prepared OK!
Waiting for the phone to boot...
Phone is in flash mode...
CMT blocks: 1434, APE blocks: 0
Erasing cmt...
Send CFG...
Processing C:\Program Files\Common Files\Nokia\DataPackage\Products\RM-123\rm123_145_30005.100.mcusw...
Erasing cmt zone 00000000 - 000006BF ...
Erasing cmt zone 000006C0 - 0000FFFF ...
Erasing cmt zone 00010000 - 0007FFFF ...
Erasing cmt zone 000A0000 - 0021FFFF ...
Erasing cmt zone 00220000 - 011DDFFF ...
Erasing cmt zone 011DE000 - 011DEFFF ...
Erasing cmt zone 011DF000 - 011DFFFF ...
Processing C:\Program Files\Common Files\Nokia\DataPackage\Products\RM-123\rm123_145_3005.10.ppm_cvf...
Erasing cmt zone 011E0000 - 016DFFFF ...
Processing C:\Program Files\Common Files\Nokia\DataPackage\Products\RM-123\rm123_145_30005.10.image_cvf...
Erasing cmt zone 016E0000 - 01E7FFFF ...
Erasing cmt zone 01E80000 - 01FDFFFF ...
Writing cmt...
Processing C:\Program Files\Common Files\Nokia\DataPackage\Products\RM-123\rm123_145_30005.100.mcusw...
Sending CMT HASH for NOLO
Sending CMT HASH for KEYS
Sending CMT HASH for PRIMAPP
Sending CMT HASH for PASUBTOC
cmt->PAPUB_CERTIFICATE_DATA_BB5 block detected
cmt->PAPUB_CERTIFICATE_DATA_BB5 block detected, sending...
Sending CMT HASH for UPDAPP
Sending CMT HASH for DSP0
Sending CMT HASH for MCUSW
Sending CMT HASH for PMM_CONF
Sending CMT HASH for SBIF_CONFProcessing C:\Program Files\Common Files\Nokia\DataPackage\Products\RM-123\rm123_145_3005.10.ppm_cvf...
Processing C:\Program Files\Common Files\Nokia\DataPackage\Products\RM-123\rm123_145_30005.10.image_cvf...
Rebooting...
Restarting CMT...
Pooling phone...
MCUSW: V 05.1021-12-06
RM-145(c) Nokia
APESW: (null)
VariantSW: (null)
Prodcode: 0535522
DCT4/BB5 counter: 22
Done!
============================================================================
So simply if u face this problem (CMT Flash Data: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF)just try dead usb flashing because not every time its hardware problem.
China N95 video Converter tested 100% ok
STEP:
1. 1st Setup the "Microsoft .NET Framework 3.0"
2. Convert Video with mehedi.h.j Converter.
3. For China N95 convert from normal.3gp = .3GP_convert
:: download :: Microsoft .NET Framework 3.0
Download N95 China video Converter Part1 and Part2
MCU >>> Part 1 Part2 Part3 Part4 Part5 Part6 Part7 Part8 Part9 Part10 Part11 Part12 Part13.
PPM >>> Part1 Part2 Part3 Part4 .
Content page >>> Part 1 Part2 Part3 Part4 Part5 Part6.
Read More and Download......JAF 1.98.54 ready...
- improved BB5 usb flashing. N78 is supported.
- added latest jaf.ini with 1680c added in dct4+ unlock
- added latest jaf_nok4models.ini (25.07.2008)
Download http://support.phone-tools.cn/files/...JAF1.98.54.rar
Or link rapidshare: http://rapidshare.com/files/13263492...98.54.rar.html
P.SYOU MUST HAVE INSTALLED JAF SETUP 1.98.52 before unpack this in jaf folder.
3110C Restart Solution here !!!
- No need RPL !!!
- No need to flash your phone !!
For solve this problem just use following steps : (Only the order)
1- Remove sim card .
2- Remove MMc and format it by your PC.
3- Open phone without sim and without MMc .
4- Reset phone . ( go to settings >> ...) .
5- Put MMC and do formating from phone , Then do reset again to phone .
6- Put sim card to phone and power it on , Then do reset again .
7- Now phone with MMC and Sim ( Put USB to phone and back all data to MMc ).
And now phone work good 100 % , tested by me with 10 pc.
B.RShorbagy Team
Unexpected error occured.Power off the device and restart.
Anyone encountered this problem before? Phone is water damaged.When I place back cover and slide it down to use Back camera, I will get error message "Unexpected error occured.Power off the device and restart.
"However when I DO NOT put back cover and camera is in front camera, it is ok. (After I restart the phone.)
I have tested voltage of C1472(4.0V), C1473 (1.5V), R1475 and J1471(1.8V) and seem to be ok. Is it ok for C1473 to have 1.5V since in the service manual, it is suppose to be 2.8V? I checked with 6680 service manual which uses the same N7505(LP3990LDX-1.5NOPB), the correct voltage is 1.5V. Anyway, I have replaced N7505 as well.
I have also replaced Camera.
Other test is TAHVO to R4408(VIO=1.8V) to S5202 is correct.
Cek F1110 with ohm metre, must result is short.
If not, then short F1110 with jumper cable.
N73 RM-133 ME EMEA 4.0750.31.2.1 v7.0 (NEW)
Diposkan oleh Cellular-tools Labs Label: Firmware Nokia BB5
Here you can find video tutorial for Cruiser users.
CID36 DB2010 Phones:
Full Repair CID36: http://www.4shared.com/file/19753197...6_Cruiser.html
CID49 DB2010 Phones:
Repair GDFS: http://www.4shared.com/file/19622833...S_Cruiser.html
Repair/Change IMEI: http://www.4shared.com/file/19622429...I_Cruiser.html
CID51 DB2020 Phones:
Unlock: http://www.4shared.com/file/19752259...0_Cruiser.html
Full Flash: http://www.4shared.com/file/19622495...h_Cruiser.html
Will be updated.
Dont forget to request your video tutorial in this thread.
Regards!
Hi everybody,
we have just compiled updated CruiserSuite All-In-One installer v1.15.
CruiserSuite All-In-One installer v1.15
This installer includes all latest versions of all component applications of CruiserSuite, including drivers, etc.
Here is the CruiserSuite All-In-One installer Rapidshare link.
Enjoy
JAF Exe 1.98.53 ready...
- fix dct4+ asic11 unlock
Download Here
(Just replace the exe file in main folder)
- Fixed bugs from 1.48
- No need server for reset BB5 counter.
- Flashing E65 with new loaders via USB (old and new E65 supported).
- Ini files fixed to work with new loaders.
- Added 6300 v6.01 counter reset.
- Now all models loaded in list box
download clik here
JAF Setup 1.98.52 ready...
- Added latest ini for BB5 tp unlock
- improved BB5 TP unlock. Added reset counters TP option.
- improved BB5 files autoselection. Correct CNT and Variant are sellected.
- DCT4 + unlock improved. Added few models more in INI.
- Imei Tool updated for DCT4 + (asic11)
- Latest Cable Drivers 7.0.2.0
- other small reported bugs fixed
Clik here for Download.
Orginall Posted: ODM Free unlock NEW VERSION 1.19
Here is full functional cracked (smartcard emulator) of Legija’s Rocker Dongle ODM Unlock v1.19 (latest) software:
Work on following models:
Motorola W205
Motorola W206 NEW
Motorola W213 NEW
Motorola W208
Motorola W209
Motorola W215
Motorola W218
Motorola W156
Motorola W160
Motorola W175
Motorola W180
Motorola W230
Motorola W270
Motorola W377
Motorola C261
Motorola F3
SonyEricsson T250
SonyEricsson Z320
SonyEricsson Z250
PLEASE READ README.TXT from ZIP archive for more details and how to use !!!
More free stuff will come in next days … (mainly Rocker Dongle emulators)
THANKS TO Mr.ZEULA
Download software in 4 part:
Part 1
Part 2
Part 3
Part 4
Cruiser Suite SE TestPoint Full Unlocker is an application for full and permanent unlocking of SonyEricsson phones. Cruiser Suite SE TestPoint Full Unlocker can also fully repair a damaged security zone. The phone must be previously flashed with a correct firmware.
Currently supported platforms: DB2020, all CIDs up to 53.
The CruiserSuite TP Full Unlocker requires UC-20 TestPoint cable - you can buy it from any of our reseller.
All other TestPoint solutions force the phone address bus pins to 3.3V which is exceeding its maximal allowed voltage almost twice. Only the UC-20 TP cable was designed to prevent this and avoid likely flash chip damage.
Here are release notes of Cruiser Suite TP Full Unlocker v1.00:
Simple to use & failsafe
Supports all DB2020 plattform based SonyEricsson phones, all CIDs up to 53
This software is for all users who can disassemble the phone - also for inexperienced ones. (For disassembling phones, we recommend to read proper SonyEricsson service manuals.)
TP Full Unlocker does not destroy phone calibration data (so typical for SeTool ... )
For the phone safety, TestPointing requires UC-20 TP cable.
Unlike other amateur solutions which use external battery connection to the TP, our software uses specially designed UC-20 cable which can handle different bus voltages and prevents any potential flash chip damage.
TP is done in two stages. Once you complete TP stage 1 you don't need to repeat it anymore. Phone is then bootable via the 2nd testpoint anytime.
You can download the software from this Rapidshare link.
Cruiser+ is the first standalone software for unlocking, changing language, changing customizations and repairing of new Sony Ericsson phones. Cruiser+ now supports Cruiser UC-20 cable.
Internet connection is required no more!
Besides, Cruiser+ includes complete Fighter functionality.
We have just released new version of Cruiser+ 13.20.
Here is the release info:
Cruiser software now supports Cruiser UC-20 cable. Updated built-in customizations. [also in Cruiser]
Updated TAC list for K320i, K530i, K770i, K800i, S500i, W200i, W380i, W580i, W610i, W660i. [also in Cruiser]
Fixed a minor bug related to W350 phones. [also in Cruiser]
Solved an issue with some DB2012 phones. [also in Cruiser]
Several internal software modules have been updated. [also in Cruiser]
Here is the Rapidshare link.
ENJOY
Unlocking DB2012 - CID52 based phone with CS TestPoint Unlocker
Diposkan oleh Cellular-tools Labs Label: CruiserCruiser Suite SE TestPoint Unlocker is an application for unlocking SonyEricsson phones. Currently supports only an Unlock-by-Patch, so the phone must be previously flashed with the desired firmware.
Currently supported platforms: DB2012 - CID52 only
Currently supported phones: Sony Ericsson W200, W300, W810.
Installation
1. Run the installer file and follow the installation wizard’s instructions
Cable
Cruiser Suite SE TestPoint Unlocker requires a new Cruiser UC20 cable. The Cruiser UC20 cable consists of:
a data cable
power supply clips
a testpoint needle
Preparation
1. Make sure the phone has the desired firmware already, otherwise flash it with your favorite flashing tool.
2. Prepare the phone for the testpoint unlock.
- remove the phone cover
- make sure the Pin27 is clean and accessible
Note: we recommend to use a binocular microscope for either preparation and testpoint connecting
Unlocking procedure
1. Make sure Cruiser+ Dongle is plugged in your computer. Card ID must end with “-07”.
2. Run SeTestPointUnlocker.exe
3. Choose the phone model.
4. Connect the data cable and power supply clips to the phone.
5. Double-click on the appropriate cruiser UC20 serial cable.
6. Wait until the program asks you to connect the testpoint.
7. Connect the testpoint needle to Pin27.
8. When informed, the testpoint may be released, the program continues with unlock procedure.
9. Disconnect the cabling from the phone when program finishes.
video unlocking w200 with UC-20
http://fr.youtube.com/watch?v=NSPLwtEE9RM
Manufacture is in full process.
Cruiser Team
Unlock red CID50 and red CID51 phones via codes (Cruiser Plus only)
Diposkan oleh Cellular-tools Labs Label: CruiserCaution:
Please read the following instructions carefully!
Not following the instructions exactly may result in severe problems with phone.
Description:
This procedure unlocks red CID50/51 DB2012 phones correctly unlike other tools.
Phones are unlocked in as clean and correct way as possible, by entering unlocking codes by the user.
Reflashing the phone unlocked this way does not cause phone to relock itself unlike phones unlocked by other tools.
Prerequisities:
·Be sure to have downloaded and installed all relevant Cruiser Firmware Restore packages for DB2012 phones.
·Ensure the phone battery is fully charged.
·Make a GDFS backup using our GDFS reader software [for free].
·Make a security zone backup using our GDFS reader software [for free].
·Ensure you have at least one server credit available.
·One DCU-60 or DCU-65 cable.
Unlocking procedure:
·Turn the phone on, then by pressing the >*<<*<* "secret" key sequence enter phone service menu. Go to the Service info submenu, then select the Software info item. Write down the first 2 or 3 lines describing the phone firmware version.
·Attach the phone normally, via DCU-60 or DCU-65 cable.
·Go to the Security RSA tab and press the Unlock RSA button. One server credit will be deducted.
·Note: Now the first 768KB of main firmware is overwritten, so it has to be restored or reflashed by a suitable main FW flash file.
·Press the Restore firmware button. This operation restores the first 768KB damaged by the Unlock RSA operation provided the respective restoral file is found. If this operation fails, you need to reflash the whole main firmware by the same firmware version as written down in the first step.
·Now go to the Locks tab and press the Read codes button. Wait a while, valid unlocking and relocking codes will be shown.
·Turn the phone off (e.g. by pressing the
·Disconnect the phone from the cable, turn it on and by pressing the <**< "secret" key sequence enter the phone unlocking menu. Select locked items and enter the respective codes when asked.
Posts
